J!ve Funfly ARTF2

The J!VE has been developed for top level competition flying, but is equally well suited for the rough and tumble of normal club use due to its tough yet exceptionally lightweight construction. Designed with the ability to fly extremely slowly yet with outstanding manoeuvrability, the J!VE can take off and land on the smallest of patches. On low rates the J!VE makes a great second model, but increase them and it becomes a fantastic 3D/Fun Fly model. The large surfaces combined with light wing loading and forgiving handling mean you can try those manoeuvres you have only previously dared attempt on the simulator!

Every part of the design has been thought out with simple design ideas like a braced wire undercarriage to help absorb those less than perfect landings/touch & gos, to the use of a double layer of balsa sheeting in the centre of the wing so the wing bands don't cause any damage.

The wing has been carefully designed to keep it both lightweight and tough. The aerofoil is thinner and has a different section to most traditional funfly models, allowing it to penetrate into the wind better on breezy days and increases the glide ratio. As with many modern 3D aircraft, the J!VE comes fitted with Side Force Generators (Tip plates) which act to increase the side area enough to allow the J!VE in knife edge, a first in its class! They also have another benefit, when the J!VE is turning tightly they reduce the tip stall and help the aircraft track better at slowspeeds. This is particularly useful during limbo or touch and go competitions.

• Pre-Built Balsa & Ply Structure
• Pre-Covered in High Quality Film
• Braced Wire Undercarriage
• Reinforced Wing Centre Section
• Large Control Surfaces
• Efficient Aerofoil Wing Section

Give the J!VE a go… you won't be disappointed!

Recommended Equipment:
IC Engine: Irvine .36 (APC 10x5) or Irvine .39 (APC 11x4)
Radio: 4+Channel
Servos: 4x New Power XLD-37HB (Flight Controls) & 1x New Power XL-16HM (Throttle)
RX Battery: 4.8v 1000mAh Ni-MH SquareThe J!VE has been developed for top level competition flying, but is equally well suited for the rough and tumble of normal club use due to its tough yet exceptionally lightweight construction. Designed with the ability to fly extremelyslowly yet with outstanding manoeuvrability, the J!VE can take off and land on the smallest of patches. On low rates the J!VE makes a great second model, but increase them and it becomes a fantastic 3D/Fun Fly model. The large surfacescombined with light wing loading and forgiving handling mean you can try those manoeuvres you have only previously dared attempt on the simulator! Every part of the design has been thought out with simple design ideas like a braced wireundercarriage to help absorb those less than perfect landings/touch & gos, to the use of a double layer of balsa sheeting in the centre of the wing so the wing bands don't cause any damage. The wing has been carefully designed to keep itboth lightweight and tough. The aerofoil is thinner and has a different section to most traditional funfly models, allowing it to penetrate into the wind better on breezy days and increases the glide ratio. As with many modern 3D aircraft,the J!VE comes fitted with Side Force Generators (Tip plates) which act to increase the side area enough to allow the J!VE in knife edge, a first in its class! They also have another benefit, when the J!VE is turning tightly they reducethe tip stall and help the aircraft track better at slow speeds. This is particularly useful during limbo or touch and go competitions. • Pre-Built Balsa & Ply Structure • Pre-Covered in High Quality Film • Braced WireUndercarriage • Reinforced Wing Centre Section • Large Control Surfaces • Efficient Aerofoil Wing Section Give the J!VE a go… you won't be disappointed! Recommended Equipment: IC Engine: Irvine .36 (APC 10x5) orIrvine .39 (APC 11x4) Radio: 4+ Channel Servos: 4x New Power XLD-37HB (Flight Controls) & 1x New Power XL-16HM (Throttle) RX Battery: 4.8v 1000mAh Ni-MH Square