FX22+R7008SB 2,4 GHz EU(No chgr)

The Futaba FX22 uses Futaba's FASSTest technology to deliver superior transmission reliability and an extremely precise, direct steering feel. Combining a comprehensive range of functions and high-level Futaba build quality the FX22 is the perfect console transmitter for all discerning pilots. The tried and tested, robust transmitter housing of the FX transmitter series offers optimal ergonomics and easy-to-reach controls. A large, centrally located, high-resolution 128x64px display (with backlight) ensures good readability in all lighting conditions. The graphically guided user interface, with the well-known simple Futaba menu structure, ensures easy operation. Centrally arranged linear slides and rotary dials are free to assign to any function.

• 14-channel remote control system with FASSTest 2.4 GHz technology
• Superior noise immunity by combining the advantages of DSSS and FHSS modulation
• Integrated 32-channel telemetry system
• Up to 1000m telemetry range
• Telemetry real-time display in large display
• Voice over optional headphones with 3.5 mm jack plug
• Melody and sound output (optionally via internal beeper or optional headphones)
• Vibration alarm
• 74x38.5 mm backlit LC display (128 x 64 dot)
• S.BUS technology for fully digital integration of S.BUS servos, S.BUS controllers and S.BUS sensors
• Fully equipped 14-channel transmitter with 20 (22) freely programmable controls
• Precise joystick with open-stick mechanism and 12-bit resolution, backlash-free, double ball bearing
• Simple programming through clear menu navigation

Transmission System
• 14 channels
• FASSTest Technology (Futaba Advanced Spread Spectrum Technology) l.
• 100 mW transmission power
• Real-time response
• Very high range> 3000m
• Ultra-fast, direct, continuous digital modulation for shortestresponse times
• Switchable FASSTest high-speed mode for ultra-fast control of 6.3 ms digital servos (12-channel, reduced telemetry functions)
• Easy Link - extremely simple, fast binding procedure between transmitter and receiver
• Extremely fast and safe automatic re-binding even under difficult conditions
• Intelligent servo timing for smooth servo control and prevention of servo runtime differences
• Dual Antenna Diversity - lightning-fast switching between two receiving antennas for optimum reception signal quality (depending on the receiver)
• Pre-Vision - FASST / FASSTest receivers continuously scan the input signal and apply an intelligent Futaba error correction
• No reaction speed loss even with heavily occupied frequency band
• Integrated range test function to check the range before starting
• Modulation mode switchable to FASST or FHSS for backward compatibility with existing Futaba components

Telemetry System
• Synchronized, bidirectional communication between transmitter and receiver with high telemetry data rate
• 32 telemetry channels
• Up to 1,000 m telemetry range
• Real-time display of telemetry data on an integrated display
• Voice over optional headphones with 3.5mm jack plug
• Voice output control via freely selectable switches
• melody and sound output (via internal beeper or optional headphones)
• vibration alarm
• Data recording of control signals (stick movements) and telemetry data on SD card
• PC evaluation software for recorded telemetry and GPS data as well as control signals
• Receiver signal strength indicator to monitor the range
• Distance warning system (with optional GPS sensor) for safe flights at the line of sight
• Receiver low voltage Warning System for monitoring the receiver battery
• Freely configurableoutput of telemetry data via display, sound, voice and vibration

Ergonomic Design
• Precision joysticks with 12-bit (4,096 steps) resolution for precise and sensitive control
• The "open-stick" mechanism of the joysticks is ball-bearing and virtually free of play
• 74x38.5mm high-contrast backlit display (128x64 dot) for best readability even in strong sunlight
• Graphical user interface and intuitive cap-touch wheel (with key lock) for easy operation of all functions
• 9 languages to choose from: German, English, French, Italian, Spanish, Czech, Russian, Japanese or Dutch
• Unified, intuitive Futaba operation guide for easy transition
• Control elements freelyassignable
• Channel assignment freely assignable
• Completely expanded with 18 controls: 6 switches, 2 rotary encoders, 2 linear slides, plus 2 optional stick switches and switches
• 2 linear slides allow convenient operation of additional functions
• For all control transmitters (also switches etc.) freely selectable trimmer selection
• Hardware reversal for all encoders and switches for free definition of the switching direction
• Model memory direct selection in the start display for fast model selection
• Freely configurable user menu
• Fast switching between telemetry and home timer display
• Configurable telemetry monitor menu (1-4)
• Mode 1-4 switchable
• Teacher / student function, optionally with optional cable or wireless module
with single-function switching (teacher can enable individual functions to the student) and mix operation (teacher can override all functions)
• Freely configurable student-teacher channel assignment

S.BUS Technology
• Digital BUS technology for model sport
• Forward-looking serial control bus
• Fully digital integration of S.BUS components such as S.BUS servos, S.BUS controllers and S.BUS sensors
• S.BUS1 and S.BUS2 (bidirectional) compatible
• S.BUS components can be programmed and registered directly from the transmitter
• Serial digital signal ideal for flybarless systems, gyroscopes and battery breakers

General Features
• 30 model memory integrated, expandable as desired with SD card (up to 8 GB, SD and SD-HC), 3862 models via optional SD card
• Model memories of the T8FG, T14SG or FX-20 transmitters on SD card can be read in directly
• Graphical servo monitor for clear display of all servo paths with servo test function
• Wide receiver voltage range of 3.6V to 8.4V for flexible choice of receiver battery
• Future-proof through software update capability via SD card
• Field-proven mixer menus for programming all servos and mixing functions depending on the model type
• Model type dependent special mixing programs for engine models (2-6 flaps), sailor models (2-8 flaps) and helicopters (6 swashplate types)
• 5 flight states (heli and glider menu) freely programmable for each model memory for optimal setting of each flight condition
• Flight State Switching with Priority Allocation and Switch Delay for Soft Transitions
• Programs for all tail types: Normal, V-tail, Delta, flying wing, separate elevator (Ailvator)
• Servo travel adjustment with limit function for all propane channels
• Servo reversal and center adjustment for channels 1-12
• Trimmers optional depending on flight conditions
• Trimming value display in steps or%, with zero setting by trim memory
• Failsafe setting andBattery Failsafe setting
• 2 operating hour counters, one of them based on model memory
• 2 freely adjustable stopwatches with memory function
• Switchable large display of stopwatches
• Function key lock preventsunwanted entries
• Servo speed setting for all propane channels.

Motor Models
Extensive mixer menus for models with up to 6 surface servos. In addition to the choice of surface type, it is also possible to choose betweenthe tail unit variants, Normal, separate elevator with transverse function (Ailvator) and V-tail. Delta models or motorized flying wing models from 2 ... 6 wing servos are also available. These mixing menus are already preprogrammed according to themodel and contain all the necessary mixing functions.

• 5 freely assignable and switchable Dual Rate / Expo settings.
• 5 free program mixers linear or 5 point curve per model memory, optionally with / without trimming and offset mixing.
• 5-point throttle curve
• Speed setting for throttle servo
• Aileron differentiation
• mixer spoiler (Flaperon)
• mixer height spoiler (Flaperon)
• Mixer side-to-side
• Mixerside-height
• Mixer Snap Roll
• mixture adjustment
• Gyro setting
• Mixer Motor for 2-step switching of motors with individual speed setting for level 1/2 as well as back and forth

Glider Models
Also for glider models are extensive mixer menus for models with up to 8 surface servos available. Optionally with or without engine. In addition to the choice of surface type, it is also possible to choose between the tail unit variants, Normal, separate elevator with transverse function (Ailvator) and V-tail. Even wing models from 2 ... 8 wing servos are available. These mixing menus are already pre-programmed and contain all the necessary mixing functions.
• 5 flight modes per model memory, with priority assignment and adjustable switchover delay, as well as logic switching function.
• 5 free program mixers linear or 5 point curve per model memory, optionally with / without trimming and offset mixing.
• Aileron differentiation
• Path adjustment of flaps
• Mixer cross-arch
• Mixer cross-side
• Mixer spoiler vault
• Mixer height spoiler
• Mixer camber height
• Mixer side-to-side
• Mixer Butterfly with offset and delay adjustment
• Mixer Butterfly - height
• Mixer trim mix for cross, side and elevation, with speed setting and FZS switchover delay.
• Gyro setting
• Mixer Motor for 2-step switchingof motors with individual speed setting for level 1/2 as well as back and forth

Helicopter Models
The mixing menus for helicopters differ essentially by the swashplate control. All classic controls such as H1, HE3 (90 °), HR3 (120 °), H-3 (140 °), H4 and H4-X (45 °) are integrated. A special feature is the adjustable linkage compensation for the H3 and H4 types. This prevents the usual offsets in larger or asymmetrical rashes, which servos can be permanently damaged. Also, the pitch function can be adjusted in speed to avoid the difference in runtime with the HR / N3 120 ° linkage.
5 free program mixers linear or 5 point curve per model memory, optionally with / without trim and offset mixing.
• Swashplatemixer
• Swash plate ring
• 5-point pitch curve Normal, throttle preselection 1,2,3, autorotation with logic switching function
• 5-point throttle Normal, throttle preselection 1,2,3, autorotation with logic switching function
• Autorotation
• Swashplate mixer (virtual rotation)
• mixer swash plate - gas (linear / center)
• Rear Mixer - Gas (Linear / Center)
• 5-point mixer pitch-tail, normal, throttle preset 1,2,3, autorotation with logic switching function
• mixture adjustment
• Rotary mixer (rear) with 3 rates and fine trim adjustment
• Rotary mixer (swash plate) with 3 rates and fine trim adjustment
• Speed controller with 3 ratesand fine trim setting

Included in the Box
• Transmitter FX22 FASSTest
• Receiver R7008SB FASSTest
• Switch cable
• Screwdriver
• Printed manual